Famco Chimney Cap & Crown Nationwide

Famco Chimney Cap & Crown in Leesburg: What to Know First

We repair and replace Famco chimney caps and crowns for homeowners across Leesburg as an independent Famco service provider, which means we’re not tied to factory service scheduling and we don’t have to sell you OEM parts when a better aftermarket option exists. Most Famco cap replacements run $340-$680 installed, crown repair runs $290-$750 depending on damage, and crown coating falls between $450-$900. You’ll get a written price before anything starts, camera photos of what we found, and a warrantied job backed by our 365-Day Done Right Promise.

Call (571) 601-3174

This page is for Leesburg homeowners who already know their Famco cap or crown is failing, and want straight answers about cost, parts, and whether repair beats replacement. Call (571) 601-3174 and we’ll schedule a camera-scan inspection, then walk you through what we find on the spot. No “call for a quote” game; the price comes to you in writing.

How Famco Products Fail - and How We Fix Them

Famco builds solid caps, but every brand has weak points. Here’s what we actually see on Leesburg roofs, specifically with Famco units:

• Famco Standard Series cap (galvanized): rust-through at the cage-to-base seam. The galvanized sheet on the Standard line holds up fine for the first decade, but the seam where the mesh cage meets the base plate is spot-welded, and those welds become rust points. Water sits on the base flange after rain and eats through the weld. We replace with the Famco F-series stainless or an equivalent-grade aftermarket stainless cap, and we seal the new base with high-temp silicone so the same water pooling doesn’t repeat.
• Famco Custom/Multi-Flue cap on older Leesburg masonry chimneys: wind-lift from undersized fasteners. Famco caps ship with set-screw style fasteners meant for vertical flue tile. But a lot of the older brick chimneys in Leesburg, especially near Balls Bluff Road and the historic district, have flue tile that’s chipped or slightly out-of-round. The stock screws only bite on the high spots of the tile, and high wind in March walks the cap loose. We drill and through-bolt the cap skirt when tile condition allows, or we fabricate a fitted base ring that grabs the full perimeter. The cap should not move when you push on it; if yours does, that’s the fix.
• Famco Mortar Guard crown sealer on stock crowns: cracking from freeze-thaw, not from bad product. Famco’s Mortar Guard is a good coating when applied to a crown that’s structurally sound. The issue comes when someone coats a crown that’s already spalling - crumbling at the edges - without repairing the concrete first. Leesburg gets enough freeze-thaw cycles that water gets into the cracks, freezes, and pops the coating off in sheets. The correct sequence is repair the crown, then coat. We see a lot of failed coatings that were applied over damage. That’s not a Famco product problem; that’s a prep problem.
• Famco Draft-King series caps: screen clogging on wood-burning flues. The Draft-King’s angled hood design works well for reducing down-drafts, but the smaller mesh on that line loads up with creosote faster than a standard cage. If a Leesburg homeowner burns wood regularly and skips a year of sweeping, the Draft-King screen becomes a draft restriction. We remove the cap, chemical-clean the screen and hood, and in cases where the client burns a lot, we’ll suggest switching to a larger-mesh cage or a standard cap. It’s not always a product failure; it’s a maintenance issue that Famco’s own instructions don’t emphasize enough.
• Famco stainless steel caps on chimneys with clay flue tile: galvanic loosening at the set screws. Stainless against clay doesn’t galvanically corrode, but the thermal expansion rate difference is real. Flue tile heats up, expands, and works against the screw over a season or two. The fix is simple: we re-tighten using impact force on every sweep, and we add a bead of high-temp sealant at the screw points so they don’t back out again. If it’s already damaged beyond tightening, we move to through-bolts.

Our Famco Chimney Cap & Crown Process

Every Famco job follows the same sequence, whether it’s a simple cap swap or a full crown rebuild:

1. 1
   Call and talk to a person. You reach our office, not a phone tree. We book a specified two-hour window, and you get a text when the technician is on the way. Clause 2 of the Haven Standard: arrive on schedule.
2. 2
   Camera-scan inspection, same visit. The technician runs a camera down the flue and documents everything: the crown condition from the roof, the cap fitment, the flue tile interior, and the smoke chamber if accessible. Every job gets the full NFPA 211 Level 2 inspection, not a flashlight peek. This has been our default since 2009 and is written into Clause 4 of the Haven Standard.
3. 3
   Parts decision, on the roof, with you on the phone. We measure the flue, check the Famco part number if the cap is legible, and determine whether OEM Famco or a quality aftermarket equivalent fits better. If the crown is cracked but not spalling, we quote repair. If it’s spalling, we quote a proper rebuild and coating. You see the photos before you approve any of it.
4. 4
   Written price, written scope, written warranty. You get all three before the tech begins work. Not after, not verbal, not “we’ll see when we get up there.” Clause 1 of the Haven Standard: have it in writing.
5. 5
   The work. Cap installation or replacement, crown repair, crown coating, or full crown rebuild. For multi-flue Famco caps, we verify airflow on each flue after mounting and adjust the positioning. On crown coating jobs, we apply the coating in two passes, not one thick coat.
6. 6
   Documented proof and the 365-Day Done Right Promise. You get a photo record of the completed work, including the interior camera footage if it applies. Every job is stamped under the Haven Standard. If something’s not right within 365 days, we make it right. That’s the entire promise.

Before

After

What Famco Chimney Cap & Crown Costs in Leesburg

Here’s what Famco work costs in the Leesburg market, in real numbers:

What moves the price: roof pitch and access, whether the existing flue tile is square enough for a stock cap, and whether the crown needs repair before coating or full replacement. A cap on a steep, slate-roofed house near the historic district costs more than the same cap on a ranch with a walkable roof. You won’t be guessing: every quote is a written number delivered before work starts. Call (571) 601-3174 and we’ll give you a real price, not a range that turns into a surprise.

Why Leesburg Homeowners Call Level Two Chimney Leesburg for Famco Work

We’ve completed more than 38,000 chimney inspections and cleanings since 2009, and every single one included a written price before work started and a documented photo record when it was done. That’s non-negotiable. The camera doesn’t lie, and neither does the price we write down before we start.

Our technicians are background-checked and uniformed, license information is on every page, and you’ll know the name of the tech assigned to your job before they arrive. If you have a competitor’s written estimate for Famco work, we’ll do a Free Second Opinion on it. And if the job calls for something beyond Famco - a liner repair using DuraFlex or HeatShield products, a Gelco patch, or a full liner rebuild - we handle those brands too, so you’re not dealing with two companies for one chimney.

FAQs